merck millipore,默克密理博,S7117,ApopTag Plastic Coverslip

搜索"Merck Millipore 密理愽"产品

Merck Millipore 默克密理愽

当前位置：首页 > >Merck Millipore > 生命科学研究
生命科学研究

merck millipore,默克密理博,S7117,ApopTag Plastic Coverslip
产品名称：ApopTag Plastic Coverslip
产品型号：S7117
APOPTAG Plastic Coverslips are designed to be custom fitted to the specific APOPTAG kit application.

merck millipore,默克密理博,S7117,ApopTag Plastic Coverslip

产品介绍

merck millipore,默克密理博,S7117,ApopTag Plastic Coverslip

描述
产品目录编号	S7117
品牌系列	Chemicon®
商名	Chemicon ApopTag
描述	ApopTag® Plastic Coverslip
概述	APOPTAG® Plastic Coverslips are designed to be custom fitted to the specific APOPTAG® kit application. Each coverslip has 2.5" x 1" dimensions.

应用
应用	APOPTAG Plastic Coverslips are designed to be custom fitted to the specific APOPTAG kit application.
应用说明	Plastic coverslips can be used to assure that a constant volume of solution is applied per unit of specimen area. However, their handling time slows down the protocol. Each square centimeter of plastic coverslip will require the volume of reagent indicated in Table 5 (S7100, S7101) and Table 10 (S7110, S7111, S7160), so that the reagent volume applied per unit of tissue area can be held constant. The surface to be covered is always equal to the area of the plastic coverslip, not the area of the specimen. Plastic coverslips may be trimmed to any desired size and shape. The kit's yield of specimens will be reduced if larger than standard coverslips are used. When using ApopTag® Kits that contain the anti-digoxigenin antibodies (S7100, S7101, S7110, S7111), plastic coverslips can be used during the incubation steps with the following reagents: WORKING STRENGTH TdT, and the ANTI-DIGOXIGENIN ANTIBODY. When using the ApopTag® Fluorescein Direct Kit (S7160), the plastic coverslips can be used during incubation steps with WORKING STRENGTH TdT. A basic coverslip method is described as follows: To make a pair of "standard area" (~5 cm2) specimen coverslips, cut a plastic coverslip (provided) into two equal halves, and fold up a 1 cm handling tab across the width, then crease sharply (See Figure 3 in insert). Drain one slide for approximately 10 seconds, and then tap off drops on a paper towel on the benchtop. Blot back and sides of the slide with a folded wipe. Carefully blot the area around the tissue section or cells, or else vacuum up solution using a pipette attached to an aspirator vacuum. Apply reagent solution to one end of the area to be covered, using a dropper bottle or pipette as required. Grasp the plastic coverslip by the handling tab and touch its opposite end to the droplet of reagent on the slide. Slightly arching the coverslip, roll it slowly downward, causing the solution to spread by capillary action. If solution does not spread evenly, tilt the slide until the flow reaches all edges. Apply plastic coverslips to microscope slides so as to minimize trapped air bubbles, which may cause variable enzyme reaction or detection. Place the slide across the pipettes, face-up and level, inside the humidified chamber. The slide edges should not touch anything so as to prevent drainage of the reagent.

应用

APOPTAG Plastic Coverslips are designed to be custom fitted to the specific APOPTAG kit application.

应用说明

Plastic coverslips can be used to assure that a constant volume of solution is applied per unit of specimen area. However, their handling time slows down the protocol. Each square centimeter of plastic coverslip will require the volume of reagent indicated in Table 5 (S7100, S7101) and Table 10 (S7110, S7111, S7160), so that the reagent volume applied per unit of tissue area can be held constant. The surface to be covered is always equal to the area of the plastic coverslip, not the area of the specimen.

Plastic coverslips may be trimmed to any desired size and shape. The kit's yield of specimens will be reduced if larger than standard coverslips are used.

When using ApopTag® Kits that contain the anti-digoxigenin antibodies (S7100, S7101, S7110, S7111), plastic coverslips can be used during the incubation steps with the following reagents: WORKING STRENGTH TdT, and the ANTI-DIGOXIGENIN ANTIBODY. When using the ApopTag® Fluorescein Direct Kit (S7160), the plastic coverslips can be used during incubation steps with WORKING STRENGTH TdT.

A basic coverslip method is described as follows:

To make a pair of "standard area" (~5 cm2) specimen coverslips, cut a plastic coverslip (provided) into two equal halves, and fold up a 1 cm handling tab across the width, then crease sharply (See Figure 3 in insert).

Drain one slide for approximately 10 seconds, and then tap off drops on a paper towel on the benchtop. Blot back and sides of the slide with a folded wipe. Carefully blot the area around the tissue section or cells, or else vacuum up solution using a pipette attached to an aspirator vacuum.

Apply reagent solution to one end of the area to be covered, using a dropper bottle or pipette as required.

Grasp the plastic coverslip by the handling tab and touch its opposite end to the droplet of reagent on the slide. Slightly arching the coverslip, roll it slowly downward, causing the solution to spread by capillary action. If solution does not spread evenly, tilt the slide until the flow reaches all edges.

Apply plastic coverslips to microscope slides so as to minimize trapped air bubbles, which may cause variable enzyme reaction or detection.

Place the slide across the pipettes, face-up and level, inside the humidified chamber. The slide edges should not touch anything so as to prevent drainage of the reagent.

产品使用声明
使用声明	Unless otherwise stated in our catalog or other company documentation accompanying the product(s), our products are intended for research use only and are not to be used for any other purpose, which includes but is not limited to, unauthorized commercial uses, in vitro diagnostic uses, ex vivo or in vivo therapeutic uses or any type of consumption or application to humans or animals.