merck millipore,默克密理博,100514,70%高氯酸

搜索"Merck Millipore 密理愽"产品

Merck Millipore 默克密理愽

级别值
ACS,ISO,Reag. Ph Eur

描述
产品目录编号	100514

产品信息
级别	ACS,ISO,Reag. Ph Eur
HS代码	2811 19 80

GHS安全信息
危害性图示
危害性声明	H271: 可能引起火灾或爆炸；强氧化剂。 H290: 可能腐蚀金属。 H314: 造成严重皮肤灼伤和眼损伤。
注意事项声明	P210: 切勿受热。 P280: 戴防护手套/穿防护服/戴防护眼罩/戴防护面具。 P301 + P330 + P331: 如误吞咽：漱口。不要诱导呕吐。 P305 + P351 + P338: 如进入眼睛：用水小心冲洗几分钟。如戴隐形眼镜并可方便地取出，取出隐形眼镜。继续冲洗。 P308 + P310: 如有接触或有疑虑：立即呼叫中毒控制中心或就医。
提示语	危险
储存类别	5.1A 强氧化性危险物质
WGK	WGK 1 轻度的水危害
一次性	22 无机的过氧化物及溴,碘一类的氧化剂可以用酸性的硫代硫酸钠溶液(编号:106512)使成无害. 第D类.

安全信息
危害性符号	Oxidising Corrosive
危险种类	????, ?????
R相	R 5- 8-35 Heating may cause an explosion.Contact with combustible material may cause fire.Causes severe burns.
S相	S 23-26-36-45 Do not breathe vapour.In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.Wear suitable protective clothing.In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).

运输信息
申报（铁路和陆路）ADR、RID	UN 1873 Perchlorsäure, 5.1 (8), I
申报（空运）IATA-DGR	UN 1873 PERCHLORIC ACID, 5.1 (8), I
申报（海运）IMDG-代码	UN 1873 PERCHLORIC ACID MORE THAN 50% BUT NOT MORE THAN 72%, 5.1 (8), I, Segregation Group: 1 (Acids)

规格
规格
Assay (acidimetric)	70.0 - 72.0 %
Colour	≤ 10 Hazen
Chlorate (ClO₃)	≤ 10 ppm
Chloride (Cl)	≤ 3 ppm
Free chlorine	≤ 0.5 ppm
Phosphate and Silicate (as SiO₂)	≤ 5 ppm
Sulphate (SO₄)	≤ 10 ppm
Total nitrogen (N)	≤ 10 ppm
Heavy metals (as Pb)	≤ 1 ppm
Ag (Silver)	≤ 0.1 ppm
Al (Aluminium)	≤ 0.05 ppm
As (Arsenic)	≤ 0.05 ppm
Ba (Barium)	≤ 0.02 ppm
Be (Beryllium)	≤ 0.02 ppm
Bi (Bismuth)	≤ 0.1 ppm
Ca (Calcium)	≤ 0.5 ppm
Cd (Cadmium)	≤ 0.05 ppm
Co (Cobalt)	≤ 0.05 ppm
Cu (Copper)	≤ 0.1 ppm
Fe (Iron)	≤ 1.0 ppm
Ge (Germanium)	≤ 0.05 ppm
Hg (Mercury)	≤ 0.005 ppm
K (Potassium)	≤ 0.1 ppm
Li (Lithium)	≤ 0.02 ppm
Mg (Magnesium)	≤ 0.5 ppm
Mn (Manganese)	≤ 0.02 ppm
Mo (Molybdenum)	≤ 0.05 ppm
Na (Sodium)	≤ 0.5 ppm
Ni (Nickel)	≤ 0.1 ppm
Pb (Lead)	≤ 0.05 ppm
Sr (Strontium)	≤ 0.02 ppm
Ti (Titanium)	≤ 0.1 ppm
Tl (Thallium)	≤ 0.05 ppm
V (Vanadium)	≤ 0.05 ppm
Zn (Zinc)	≤ 0.1 ppm
Zr (Zirconium)	≤ 0.1 ppm
Residue on ignition (as sulphate)	≤ 30 ppm
Identity	passes test
Density (d 20/20)	approx. 1.7
Conform to ACS, ISO, Reag.Ph Eur.